Over-Axle Bearing Press
Regular price £18.00
Over-axle bearing press tool for mountain bike and road bike wheel hubs
*** Buy one, get one 30% off any mix of pullers and presses (applies to individual tools only, not kits) ***
This tool is designed to install the sealed cartridge bearings that are found on many brands of bicycle hub. This version of our press is designed to fit over the axles that protrude through the centre of the bearings on many hub designs, such as Hope and DT Swiss.
If the axle protrudes through the bearing, and the axle can't be removed before removing the bearing (sometimes called a captive axle), then this press is a better choice than our regular press.
The tool consists of a set of drifts (sometimes called spacers or bushings) machined to closely match the diameter of the axle and the bearing€™s outside diameter, and a threaded rod to pull the drifts together. The long drift is long enough to be used on the long drive-side of the hub's axle.
Some sizes come as combos; i.e., 6903 is only available in combination with 6803. The reason for this is that the 6903 uses a 6803 press together with an adaptor ring to match the larger outside diameter of 6903.
Each set of drifts can be purchased with either T-bar handles or simple nuts. Both of these options include the drifts and threaded rod. The T-bar handles make the tool super-easy to use, while the nuts are a functional and cheaper option and are used with normal spanners. The spacer and handles are compatible with all of our other bearing presses.
(Note that the 10mm and 12mm versions of the over-axle press (that's 6000, 6001, 6800, 6801, 6900, 6901) use a 5mm threaded rod so that they can be used with most quick-release hubs. They therefore aren't compatible with our T-bar handles, which use an 8mm threaded rod)
The tool is shaped to press the outer race of the bearing, meaning that no stress is placed across the bearings, prolonging bearing life and protecting the hub.
- Specifically designed for bearings that have to be pressed over an axle
- Bearing are installed straight, kind to hub
- Shipping is fast and free in the UK!
Unlike some other bearing press designs, this design closely fits the bearing€™s outside diameter and hub axle diameter to ensure that the tool remains accurately centred and the bearings are pressed in straight.
How To Use
The press tool is simple to use:
Install the bearings and axle loosely. Slide the small 'tube' drift over the short end of the axle together with and necessary adaptor ring required to match the outside diameter of the bearing. Slide the longer 'tube' drift together with any necessary adaptor ring over the other end of the axle.
Slide the threaded rod through the centre of the axle. Tightening the nuts or handles draws the spacers together, pressing the bearing into place.
We prefer pressing in one side at a time. The hub axle can be inserted through the first bearing and the spare drift inserted in place of the second bearing to keep everything aligned.
If the bore through the axles less than 8mm (usually just the case with QR hubs), the threaded rod cannot be used. However, the spacers can still be used to tap the bearing in with a hammer.
We offer several options to customise your press to suit your specific needs, including:
- Extensions to allow the handles to stand clear of any obstructions or to allow you to press a bearing deep into a recess
- Thrust bearings to make the tightening of the press super smooth!
The over-axle design is common in rear hub bodies (including Hope and DT) but less common in front hubs and quite unusual in freehubs.
If your hub or freehub doesn't have a captive axle then you would be better with our normal press. Without a captive axle there is nothing to keep the over-axle design centred on the bearing, while our normal press has a section that protrudes into the bearing to maintain accurate alignment.
If you find that you need a mix of over-axle and normal presses then our 30% 'second item discount' can be used for a mix presses and pullers. The same T-bar handles or nuts can be used for all our presses (in this case it is best to purchase the over-axle press with the handles/nuts and the normal presses as 'drifts only', as the over-axle press comes with a longer threaded rod)
We offer a comprehensive range of bearing pullers, available in all of the same sizes and kits as our bearing presses. They can even remove blind and back-to-back bearings. We offer 30% off every second item bought from our single tools menus, including mixes of pullers and presses.
If your hub is of the over-axle design then often you don't need a puller - just tap the axle with a soft mallet or block of wood - but if your design does need a puller, we've got you covered!
We aim to dispatch all orders within 1 working day
Orders within the UK will be shipped by Royal Mail RM24 (First Class)
International orders are welcomed and will be shipped by Royal Mail International Standard (Airmail). Delivery times vary but are typically 2-3 days within Europe and 5-10 days worldwide
Our tools can be selected either by the bearing size or by the bearing's standard reference code.
Standard references take the form of a three or four digit number, such as 688, or 6902 for example. These codes are often moulded onto the bearing's seal. You might see something like 6902-2RS on the seal. The first digits are the standard reference. The second part (2RS in this case) refers to the seal type and doesn't matter for tool selection.
Alternatively, tools can be selected by their inside (ID) and outside (OD) diameters and width.
Note that each tool is specific to one bearing size and can’t be used on bearings with different dimensions.
If you need any help then please feel free to email us.